27 wifi
evilsocket edited this page 2019-02-21 14:21:43 +01:00

The wifi.* modules work with a WiFi interface supporting monitor mode and packet injection and they are used to monitor and perform wireless attacks on 802.11.

The interface only needs to support monitor mode and packet injection, it'll be bettercap itself to switch it to the right mode, just make sure there aren't other processes using the same wifi interface.

Commands

command description
wifi.recon on Start 802.11 wireless base stations discovery and handshakes capture.
wifi.recon off Stop 802.11 wireless base stations discovery.
wifi.clear Clear all access points collected by the WiFi discovery module.
wifi.recon BSSID Set 802.11 base station address to filter for.
wifi.recon clear Remove the 802.11 base station filter.
wifi.assoc BSSID Send an association request to the selected BSSID in order to receive a RSN PMKID key (use all, * or ff:ff:ff:ff:ff:ff to iterate for every access point).
wifi.deauth BSSID Start a 802.11 deauth attack, if an access point BSSID is provided, every client will be deauthenticated, otherwise only the selected client (use all, * or ff:ff:ff:ff:ff:ff to deauth everything).
wifi.show Show current wireless stations list (default sorting by RSSI).
wifi.show.wps BSSID Show WPS information about a given station (use all, * or ff:ff:ff:ff:ff:ff to select all).
wifi.recon.channel CHANNEL Comma separated list of channels to hop on.
wifi.recon.channel clear Enable channel hopping on all supported channels.
wifi.ap Inject fake management beacons in order to create a rogue access point ( requires wifi.recon to run ).

Parameters

parameter default description
wifi.region BO Set the WiFi region to this value before activating the interface.
wifi.txpower 30 Set WiFi transmission power to this value before activating the interface.
wifi.rssi.min -200 Minimum WiFi signal strength in dBm.
wifi.show.manufacturer false If true, wifi.show will also show the devices manufacturers.
wifi.show.filter Defines a regular expression filter for wifi.show.
wifi.show.sort rssi asc Defines sorting field (rssi, bssid, essid, channel, encryption, clients, seen, sent, rcvd) and direction (asc or desc) for wifi.show.
wifi.show.sort asc Defines sorting direction for wifi.show.
wifi.show.limit 0 If greater than zero, defines limit for wifi.show.
wifi.hop.period 250 If channel hopping is enabled (empty wifi.recon.channel), this is the time in millseconds the algorithm will hop on every channel (it'll be doubled if both 2.4 and 5.0 bands are available).
wifi.handshakes.file ~/bettercap-wifi-handshakes.pcap File path of the pcap file to save handshakes to.
wifi.source.file If set, the wifi module will read from this pcap file instead of the hardware interface.
wifi.skip-broken true If true, dot11 packets with an invalid checksum will be skipped.
wifi.assoc.skip Comma separated list of BSSID to skip while sending association requests.
wifi.assoc.silent false If true, messages from wifi.assoc will be suppressed.
wifi.assoc.open false Send association requests to open networks.
wifi.deauth.skip Comma separated list of BSSID to skip while sending deauth packets.
wifi.deauth.silent false If true, messages from wifi.deauth will be suppressed.
wifi.deauth.open true Send wifi deauth packets to open networks.
wifi.ap.ssid FreeWifi SSID of the fake access point.
wifi.ap.bssid <random mac> BSSID of the fake access point.
wifi.ap.channel 1 Channel of the fake access point.
wifi.ap.encryption true If true, the fake access point will use WPA2, otherwise it'll result as an open AP.

Examples

Starts bettercap on wlan0, use the ticker and wifi.recon modules to create a WiFi scanner (performing channel hopping on every supported frequency):

~/ sudo bettercap -iface wlan0

> set ticker.commands "clear; wifi.show"; wifi.recon on; ticker on

Only recon on channels 1, 2 and 3:

> wifi.recon on; wifi.recon.channel 1,2,3

Sort by BSSID and filter for BSSIDs starting with F4:

> set wifi.show.sort bssid asc
> set wifi.show.filter ^F4
> wifi.show

Filter by access points starting with the string AP in their ESSID:

> set wifi.show.filter ^AP
> wifi.show

Show top 10 access points sorted by last activity timestamp:

> set wifi.show.sort seen desc
> set wifi.show.limit 10
> wifi.show

Keep deauthing clients from the access point with BSSID DE:AD:BE:EF:DE:AD every five seconds:

> set ticker.period 5; set ticker.commands "wifi.deauth DE:AD:BE:EF:DE:AD"; ticker on

Will send management beacons as the fake access point "Banana" with BSSID DE:AD:BE:EF:DE:AD on channel 5 without encryption:

> set wifi.ap.ssid Banana
> set wifi.ap.bssid DE:AD:BE:EF:DE:AD
> set wifi.ap.channel 5
> set wifi.ap.encryption false
> wifi.recon on; wifi.ap