//-----------------------------------------------------------------------------
// The FPGA is responsible for interfacing between the A/D, the coil drivers,
// and the ARM. In the low-frequency modes it passes the data straight
// through, so that the ARM gets raw A/D samples over the SSP. In the high-
// frequency modes, the FPGA might perform some demodulation first, to
// reduce the amount of data that we must send to the ARM.
//
// I am not really an FPGA/ASIC designer, so I am sure that a lot of this
// could be improved.
//
// Jonathan Westhues, March 2006
// Added ISO14443-A support by Gerhard de Koning Gans, April 2008
// iZsh <izsh at fail0verflow.com>, June 2014
// Piwi, Feb 2019
//-----------------------------------------------------------------------------
// Defining commands, modes and options. This must be aligned to the definitions in fpgaloader.h
// Note: the definitions here are without shifts
// Commands:
`define FPGA_CMD_SET_CONFREG 1
`define FPGA_CMD_TRACE_ENABLE 2
// Major modes:
`define FPGA_MAJOR_MODE_HF_READER 0
`define FPGA_MAJOR_MODE_HF_SIMULATOR 1
`define FPGA_MAJOR_MODE_HF_ISO14443A 2
`define FPGA_MAJOR_MODE_HF_SNIFF 3
`define FPGA_MAJOR_MODE_HF_ISO18092 4
`define FPGA_MAJOR_MODE_HF_GET_TRACE 5
`define FPGA_MAJOR_MODE_OFF 7
// Options for the generic HF reader
`define FPGA_HF_READER_MODE_RECEIVE_IQ 0
`define FPGA_HF_READER_MODE_RECEIVE_AMPLITUDE 1
`define FPGA_HF_READER_MODE_RECEIVE_PHASE 2
`define FPGA_HF_READER_MODE_SEND_FULL_MOD 3
`define FPGA_HF_READER_MODE_SEND_SHALLOW_MOD 4
`define FPGA_HF_READER_MODE_SNIFF_IQ 5
`define FPGA_HF_READER_MODE_SNIFF_AMPLITUDE 6
`define FPGA_HF_READER_MODE_SNIFF_PHASE 7
`define FPGA_HF_READER_MODE_SEND_JAM 8
`define FPGA_HF_READER_SUBCARRIER_848_KHZ 0
`define FPGA_HF_READER_SUBCARRIER_424_KHZ 1
`define FPGA_HF_READER_SUBCARRIER_212_KHZ 2
// Options for the HF simulated tag, how to modulate
`define FPGA_HF_SIMULATOR_NO_MODULATION 0
`define FPGA_HF_SIMULATOR_MODULATE_BPSK 1
`define FPGA_HF_SIMULATOR_MODULATE_212K 2
`define FPGA_HF_SIMULATOR_MODULATE_424K 4
`define FPGA_HF_SIMULATOR_MODULATE_424K_8BIT 5
// Options for ISO14443A
`define FPGA_HF_ISO14443A_SNIFFER 0
`define FPGA_HF_ISO14443A_TAGSIM_LISTEN 1
`define FPGA_HF_ISO14443A_TAGSIM_MOD 2
`define FPGA_HF_ISO14443A_READER_LISTEN 3
`define FPGA_HF_ISO14443A_READER_MOD 4
//options for ISO18092 / Felica
`define FPGA_HF_ISO18092_FLAG_NOMOD 1 // 0001 disable modulation module
`define FPGA_HF_ISO18092_FLAG_424K 2 // 0010 should enable 414k mode (untested). No autodetect
`define FPGA_HF_ISO18092_FLAG_READER 4 // 0100 enables antenna power, to act as a reader instead of tag
`include "hi_reader.v"
`include "hi_simulate.v"
//`include "hi_iso14443a.v"
`include "hi_sniffer.v"
`include "util.v"
`include "hi_flite.v"
`include "hi_get_trace.v"
module fpga_felica(
input spck, output miso, input mosi, input ncs,
input pck0, input ck_1356meg, input ck_1356megb,
output pwr_lo, output pwr_hi,
output pwr_oe1, output pwr_oe2, output pwr_oe3, output pwr_oe4,
input [7:0] adc_d, output adc_clk, output adc_noe,
output ssp_frame, output ssp_din, input ssp_dout, output ssp_clk,
input cross_hi, input cross_lo,
output dbg
);
//-----------------------------------------------------------------------------
// The SPI receiver. This sets up the configuration word, which the rest of
// the logic looks at to determine how to connect the A/D and the coil
// drivers (i.e., which section gets it). Also assign some symbolic names
// to the configuration bits, for use below.
//-----------------------------------------------------------------------------
/*
Attempt to write up how its hooked up. Iceman 2020.
Communication between ARM / FPGA is done inside armsrc/fpgaloader.c see: function FpgaSendCommand()
Send 16 bit command / data pair to FPGA
The bit format is: C3 C2 C1 C0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
where
C is 4bit command
D is 12bit data
shift_reg receive this 16bit frame
-----+--------- frame layout --------------------
bit | 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
-----+-------------------------------------------
cmd | x x x x
major| x x x
opt | x x x
divi | x x x x x x x x
thres| x x x x x x x x
-----+-------------------------------------------
*/
reg [15:0] shift_reg;
reg [8:0] conf_word;
reg trace_enable;
// We switch modes between transmitting to the 13.56 MHz tag and receiving
// from it, which means that we must make sure that we can do so without
// glitching, or else we will glitch the transmitted carrier.
always @(posedge ncs)
begin
case(shift_reg[15:12])
`FPGA_CMD_SET_CONFREG: conf_word <= shift_reg[8:0];
`FPGA_CMD_TRACE_ENABLE: trace_enable <= shift_reg[0];
endcase
end
always @(posedge spck)
begin
if(~ncs)
begin
shift_reg[15:1] <= shift_reg[14:0];
shift_reg[0] <= mosi;
end
end
// select module (outputs) based on major mode
wire [2:0] major_mode = conf_word[8:6];
// configuring the HF reader
wire [1:0] subcarrier_frequency = conf_word[5:4];
wire [3:0] minor_mode = conf_word[3:0];
//-----------------------------------------------------------------------------
// And then we instantiate the modules corresponding to each of the FPGA's
// major modes, and use muxes to connect the outputs of the active mode to
// the output pins.
//-----------------------------------------------------------------------------
// 000 - HF reader
hi_reader hr(
ck_1356megb,
hr_pwr_lo, hr_pwr_hi, hr_pwr_oe1, hr_pwr_oe2, hr_pwr_oe3, hr_pwr_oe4,
adc_d, hr_adc_clk,
hr_ssp_frame, hr_ssp_din, ssp_dout, hr_ssp_clk,
hr_dbg,
subcarrier_frequency, minor_mode
);
// 001 - HF simulated tag
hi_simulate hs(
ck_1356meg,
hs_pwr_lo, hs_pwr_hi, hs_pwr_oe1, hs_pwr_oe2, hs_pwr_oe3, hs_pwr_oe4,
adc_d, hs_adc_clk,
hs_ssp_frame, hs_ssp_din, ssp_dout, hs_ssp_clk,
hs_dbg,
minor_mode
);
// 011 - HF sniff
hi_sniffer he(
ck_1356megb,
he_pwr_lo, he_pwr_hi, he_pwr_oe1, he_pwr_oe2, he_pwr_oe3, he_pwr_oe4,
adc_d, he_adc_clk,
he_ssp_frame, he_ssp_din, he_ssp_clk
);
// 100 - HF ISO18092 FeliCa
hi_flite hfl(
ck_1356megb,
hfl_pwr_lo, hfl_pwr_hi, hfl_pwr_oe1, hfl_pwr_oe2, hfl_pwr_oe3, hfl_pwr_oe4,
adc_d, hfl_adc_clk,
hfl_ssp_frame, hfl_ssp_din, ssp_dout, hfl_ssp_clk,
hfl_dbg,
minor_mode
);
// 101 - HF get trace
hi_get_trace gt(
ck_1356megb,
adc_d, trace_enable, major_mode,
gt_ssp_frame, gt_ssp_din, gt_ssp_clk
);
// Major modes:
// 000 -- HF reader; subcarrier frequency and modulation depth selectable
// 001 -- HF simulated tag
// 010 -- HF ISO14443-A - removed for space...
// 011 -- HF sniff
// 100 -- HF ISO18092 FeliCa
// 101 -- HF get trace
// 110 -- unused
// 111 -- FPGA_MAJOR_MODE_OFF
// 000 001 010 011 100 101 110 111
mux8 mux_ssp_clk (major_mode, ssp_clk, hr_ssp_clk, hs_ssp_clk, 1'b0, he_ssp_clk, hfl_ssp_clk, gt_ssp_clk, 1'b0, 1'b0);
mux8 mux_ssp_din (major_mode, ssp_din, hr_ssp_din, hs_ssp_din, 1'b0, he_ssp_din, hfl_ssp_din, gt_ssp_din, 1'b0, 1'b0);
mux8 mux_ssp_frame (major_mode, ssp_frame, hr_ssp_frame, hs_ssp_frame, 1'b0, he_ssp_frame, hfl_ssp_frame, gt_ssp_frame, 1'b0, 1'b0);
mux8 mux_pwr_oe1 (major_mode, pwr_oe1, hr_pwr_oe1, hs_pwr_oe1, 1'b0, he_pwr_oe1, hfl_pwr_oe1, 1'b0, 1'b0, 1'b0);
mux8 mux_pwr_oe2 (major_mode, pwr_oe2, hr_pwr_oe2, hs_pwr_oe2, 1'b0, he_pwr_oe2, hfl_pwr_oe2, 1'b0, 1'b0, 1'b0);
mux8 mux_pwr_oe3 (major_mode, pwr_oe3, hr_pwr_oe3, hs_pwr_oe3, 1'b0, he_pwr_oe3, hfl_pwr_oe3, 1'b0, 1'b0, 1'b0);
mux8 mux_pwr_oe4 (major_mode, pwr_oe4, hr_pwr_oe4, hs_pwr_oe4, 1'b0, he_pwr_oe4, hfl_pwr_oe4, 1'b0, 1'b0, 1'b0);
mux8 mux_pwr_lo (major_mode, pwr_lo, hr_pwr_lo, hs_pwr_lo, 1'b0, he_pwr_lo, hfl_pwr_lo, 1'b0, 1'b0, 1'b0);
mux8 mux_pwr_hi (major_mode, pwr_hi, hr_pwr_hi, hs_pwr_hi, 1'b0, he_pwr_hi, hfl_pwr_hi, 1'b0, 1'b0, 1'b0);
mux8 mux_adc_clk (major_mode, adc_clk, hr_adc_clk, hs_adc_clk, 1'b0, he_adc_clk, hfl_adc_clk, 1'b0, 1'b0, 1'b0);
mux8 mux_dbg (major_mode, dbg, hr_dbg, hs_dbg, 1'b0, he_dbg, hfl_dbg, 1'b0, 1'b0, 1'b0);
// In all modes, let the ADC's outputs be enabled.
assign adc_noe = 1'b0;
endmodule